/**
  @page ADC_ExtLinesTrigger ADC_ExtLinesTrigger
  
  @verbatim
  ******************** (C) COPYRIGHT 2009 STMicroelectronics *******************
  * @file    ADC/ExtLinesTrigger/readme.txt 
  * @author  MCD Application Team
  * @version V3.1.2
  * @date    09/28/2009
  * @brief   Description of the ADC external lines trigger example.
  ******************************************************************************
  * THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS
  * WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE
  * TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY
  * DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING
  * FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE
  * CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS.
  ******************************************************************************
   @endverbatim

@par Example Description 

This example describes how to trigger ADC regular and injected groups channels 
conversion using two external line events. Discontinuous mode is enabled for regular
group channel conversion and configured to convert one regular channel on each 
external trigger.

ADC1 is configured to start regular group channel conversion on EXTI11 event.
On detection of the first rising edge on PE.11 pin, the conversion of the first regular
channel (ADC channel4) is done and its converted value is transfered by DMA to 
ADC_RegularConvertedValueTab table. On the following edge detection, the second 
regular channel (ADC channel14) is automatically converted and its converted value
is stored by DMA in the same table. The number of transmitted data by DMA, in this 
example is limited to 64 data.

The procedure is repeated for both regular channels on each EXTI11 event.
ADC1 is configured to start injected group channel conversion on EXTI15 event.
On detection of the first rising edge on PE.15 pin all selected injected channels, which
are two in this example (ADC channel11 and channel12), are converted and an interrupt 
is generated on JEOC flag rising at the end of all injected channels conversion. 
Both injected channels converted results are stored in ADC_InjectedConvertedValueTab 
table inside the interrupt routine.
The procedure is repeated for injected channels on each EXTI15 event.
The ADC1 clock is set to 14 MHz.

@par Directory contents 

  - ADC/ExtLinesTrigger/stm32f10x_conf.h  Library Configuration file
  - ADC/ExtLinesTrigger/stm32f10x_it.c    Interrupt handlers
  - ADC/ExtLinesTrigger/stm32f10x_it.h    Interrupt handlers header file
  - ADC/ExtLinesTrigger/main.c            Main program

@par Hardware and Software environment 

  - This example runs on STM32F10x Connectivity line, High-Density, Medium-Density 
    and Low-Density Devices.
  
  - This example has been tested with STMicroelectronics STM3210C-EVAL (STM32F10x 
    Connectivity line), STM3210E-EVAL (STM32F10x High-Density) and STM3210B-EVAL
    (STM32F10x Medium-Density) evaluation boards and can be easily tailored to
    any other supported device and development board.

  - STM3210C-EVAL Set-up 
    - Connect a known voltage, between 0-3.3V, to ADC Channel14 mapped on pin 
      PC.04 (potentiometer RV1), ADC Channel4 mapped on pin PA.04, ADC Channel11 
      mapped on pin PC.01 and ADC Channel12 mapped on pin PC.02.
    - Connect a push-button to pin PE.11 (EXTI Line11) and another push-button 
      to pin PE.15 (EXTI Line15).
      
  - STM3210E-EVAL Set-up 
    - Connect a known voltage, between 0-3.3V, to ADC Channel14 mapped on pin 
      PC.04 (potentiometer RV1), ADC Channel4 mapped on pin PA.04, ADC Channel11 
      mapped on pin PC.01 and ADC Channel12 mapped on pin PC.02.
    - Connect a push-button to pin PE.11 (EXTI Line11) and another push-button 
      to pin PE.15 (EXTI Line15).

  - STM3210B-EVAL Set-up 
    - Connect a known voltage, between 0-3.3V, to ADC Channel14 mapped on pin 
      PC.04 (potentiometer RV1), ADC Channel4 mapped on pin PA.04, ADC Channel11 
      mapped on pin PC.01 and ADC Channel12 mapped on pin PC.02.
    - Connect a push-button to pin PE.11 (EXTI Line11) and another push-button 
      to pin PE.15 (EXTI Line15).              
   
@par How to use it ? 

In order to make the program work, you must do the following :
- Create a project and setup all project configuration
- Add the required Library files :
  - stm32f10x_adc.c 
  - stm32f10x_dma.c 
  - stm32f10x_exti.c
  - stm32f10x_flash.c  
  - stm32f10x_gpio.c 
  - stm32f10x_rcc.c 
  - misc.c  
    
- Edit stm32f10x.h file to select the device you are working on.
  
@b Tip: You can tailor the provided project template to run this example, for 
        more details please refer to "stm32f10x_stdperiph_lib_um.chm" user 
        manual; select "Peripheral Examples" then follow the instructions 
        provided in "How to proceed" section.   
- Link all compiled files and load your image into target memory
- Run the example

@note
 - Low-density devices are STM32F101xx and STM32F103xx microcontrollers where
   the Flash memory density ranges between 16 and 32 Kbytes.
 - Medium-density devices are STM32F101xx and STM32F103xx microcontrollers where
   the Flash memory density ranges between 32 and 128 Kbytes.
 - High-density devices are STM32F101xx and STM32F103xx microcontrollers where
   the Flash memory density ranges between 256 and 512 Kbytes.
 - Connectivity line devices are STM32F105xx and STM32F107xx microcontrollers.
    
 * <h3><center>&copy; COPYRIGHT 2009 STMicroelectronics</center></h3>
 */
