/**
  @page I2C_Interrupt I2C_Interrupt
  
  @verbatim
  ******************** (C) COPYRIGHT 2009 STMicroelectronics *******************
  * @file    I2C/Interrupt/readme.txt 
  * @author  MCD Application Team
  * @version V3.1.2
  * @date    09/28/2009
  * @brief   Description of the I2C interrupt mode example.
  ******************************************************************************
  * THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS
  * WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE
  * TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY
  * DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING
  * FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE
  * CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS.
  ******************************************************************************
   @endverbatim

@par Example Description 

This example provides a description of how to manage data transfer from 
master transmitter to slave receiver and from slave transmitter to master receiver 
using interrupts.

After enabling the two I2C peripherals, both event and buffer interrupts for 
I2C1 and I2C2 and error interrupt for I2C2, the transfer in 7-bit addressing 
mode starts after I2C1 start condition generation.

First, the master transmitter I2C1 send I2C1_Buffer_Tx data buffer to the 
salve receiver I2C2. Data received by I2C2 is stored in I2C2_Buffer_Rx buffer.
Each time an event occurs on the master or the slave, it is managed in the I2C1 
or I2C2 interrupts routines, respectively. 
The PEC value is also transmitted from master transmitter to slave receiver and 
it is stored in the same reception buffer I2C2_Buffer_Rx.
The transmitted and received buffers are compared to check that all data have 
been correctly transferred (except the PEC value). This transfer status is stored 
in TransferStatus1 variable.

Once the Re-Start condition is sent, thus the second step is started and the 
I2C2_Buffer_Tx will be sent from the slave transmitter I2C2 to be recieved by 
the master receiver I2C1 and stored in I2C1_Buffer_Rx. 
Each time an event occurs on the master or the slave, it is managed in the I2C1 
or I2C2 interrupts routines, respectively. 
The transmitted and received buffers are compared to check that all data have been 
correctly transferred. This transfer status is stored in TransferStatus2 variable.

The communication clock speed is set to 200KHz.

@par Directory contents 

  - I2C/Interrupt/stm32f10x_conf.h  Library Configuration file
  - I2C/Interrupt/stm32f10x_it.c    Interrupt handlers
  - I2C/Interrupt/stm32f10x_it.h    Interrupt handlers header file
  - I2C/Interrupt/main.h            Main header file
  - I2C/Interrupt/main.c            Main program


@par Hardware and Software environment 

  - This example runs on STM32F10x Connectivity line, High-Density, Medium-Density 
    and Low-Density Devices.
  
  - This example has been tested with STMicroelectronics STM3210E-EVAL (STM32F10x 
    High-Density) and STM3210B-EVAL (STM32F10x Medium-Density) evaluation boards 
    and can be easily tailored to any other supported device and development 
    board.
    This example can't be tested with STMicroelectronics STM3210C-EVAL (STM32F10x 
    Connectivity-Line) evaluation board since the I2C2 pins (PB10 and PB11) are 
    already used by Ethernet PHY module.

  - STM3210E-EVAL & STM3210B-EVAL Set-up 
    - Connect I2C1 SCL pin (PB.06) to I2C2 SCL pin (PB.10)
    - Connect I2C1 SDA pin (PB.07) to I2C2 SDA pin	(PB.11)
    - Check that a pull-up resistor is connected on one I2C SDA pin
    - Check that a pull-up resistor is connected on one I2C SCL pin

@note The pull-up resitors are already implemented on the STM3210B-EVAL and
      STM3210E-EVAL evaluation boards.

@par How to use it ? 

In order to make the program work, you must do the following :
- Create a project and setup all project configuration
- Add the required Library files :
  - stm32f10x_i2c.c 
  - stm32f10x_rcc.c 
  - stm32f10x_gpio.c 
  - misc.c
  - system_stm32f10x.c (under Libraries\CMSIS\Core\CM3)
        
- Edit stm32f10x.h file to select the device you are working on.
  
@b Tip: You can tailor the provided project template to run this example, for 
        more details please refer to "stm32f10x_stdperiph_lib_um.chm" user 
        manual; select "Peripheral Examples" then follow the instructions 
        provided in "How to proceed" section.   
- Link all compiled files and load your image into target memory
- Run the example

@note
 - Low-density devices are STM32F101xx and STM32F103xx microcontrollers where
   the Flash memory density ranges between 16 and 32 Kbytes.
 - Medium-density devices are STM32F101xx and STM32F103xx microcontrollers where
   the Flash memory density ranges between 32 and 128 Kbytes.
 - High-density devices are STM32F101xx and STM32F103xx microcontrollers where
   the Flash memory density ranges between 256 and 512 Kbytes.
 - Connectivity-line devices are STM32F105xx and STM32F107xx microcontrollers.
   
 * <h3><center>&copy; COPYRIGHT 2009 STMicroelectronics</center></h3>
 */
