/**
  @page TIM_OCInactive TIM_OCInactive
  
  @verbatim
  ******************** (C) COPYRIGHT 2009 STMicroelectronics *******************
  * @file    TIM/OCInactive/readme.txt 
  * @author  MCD Application Team
  * @version V3.1.2
  * @date    09/28/2009
  * @brief   Description of the TIM OCInactive example.
  ******************************************************************************
  * THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS
  * WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE
  * TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY
  * DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING
  * FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE
  * CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS.
  ******************************************************************************
   @endverbatim

@par Example Description 

This example shows how to configure the TIM peripheral in Output Compare Inactive 
mode with the corresponding Interrupt requests for each channel.

The TIMxCLK frequency is set to 36 MHz, the Prescaler is set to 35999 and used in 
Output Compare Inactive Mode.
TIM2 counter clock = TIMxCLK / (Prescaler +1) = 1 KHz 

The TIM2 CCR1 register value is equal to 1000:
TIM2_CC1 delay = CCR1_Val/TIM2 counter clock  = 1000 ms
so the PC.06  is reset after a delay equal to 1000 ms.

The TIM2 CCR2 register value is equal to 500:
TIM2_CC2 delay = CCR2_Val/TIM2 counter clock = 500 ms
so the PC.07  is reset after a delay equal to 500 ms.

The TIM2 CCR3 register value is equal to 250:
TIM2_CC3 delay = CCR3_Val/TIM2 counter clock = 250 ms
so the PC.08  is reset after a delay equal to 250 ms.

The TIM2 CCR4 register value is equal to 125:
TIM2_CC4 delay = CCR4_Val/TIM2 counter clock = 125 ms
so the PC.09  is reset after a delay equal to 125 ms.

While the counter is lower than the Output compare registers values, which 
determines the Output delay, the PC.06, PC.07, PC.08 and PC.09 pin are turned on. 

When the counter value reaches the Output compare registers values, the Output 
Compare interrupts are generated and, in the handler routine, these pins are turned off.

@par Directory contents 

  - TIM/OCInactive/stm32f10x_conf.h  Library Configuration file
  - TIM/OCInactive/stm32f10x_it.c    Interrupt handlers
  - TIM/OCInactive/stm32f10x_it.h    Interrupt handlers header file
  - TIM/OCInactive/main.c            Main program
 

@par Hardware and Software environment 

  - This example runs on STM32F10x Connectivity line, High-Density, Medium-Density 
    and Low-Density Devices.
  
  - This example has been tested with STMicroelectronics STM3210C-EVAL (STM32F10x 
    Connectivity line), STM3210E-EVAL (STM32F10x High-Density) and STM3210B-EVAL
    (STM32F10x Medium-Density) evaluation boards and can be easily tailored to
    any other supported device and development board.

  - STM3210E-EVAL, STM3210B-EVAL and STM3210C-EVAL Set-up 
    - Connect the following pins to an oscilloscope to monitor the different 
      waveforms:
        - PC.06
        - PC.07
        - PC.08 
        - PC.09
  
@par How to use it ? 

In order to make the program work, you must do the following:
- Create a project and setup all project configuration
- Add the required Library files:
  - stm32f10x_flash.c 
  - stm32f10x_gpio.c 
  - stm32f10x_rcc.c 
  - stm32f10x_tim.c
  - misc.c
  - system_stm32f10x.c (under Libraries\CMSIS\Core\CM3)
      
- Edit stm32f10x.h file to select the device you are working on.
  
@b Tip: You can tailor the provided project template to run this example, for 
        more details please refer to "stm32f10x_stdperiph_lib_um.chm" user 
        manual; select "Peripheral Examples" then follow the instructions 
        provided in "How to proceed" section.   
- Link all compiled files and load your image into target memory
- Run the example

@note
 - Low-density devices are STM32F101xx and STM32F103xx microcontrollers where
   the Flash memory density ranges between 16 and 32 Kbytes.
 - Medium-density devices are STM32F101xx and STM32F103xx microcontrollers where
   the Flash memory density ranges between 32 and 128 Kbytes.
 - High-density devices are STM32F101xx and STM32F103xx microcontrollers where
   the Flash memory density ranges between 256 and 512 Kbytes.
 - Connectivity line devices are STM32F105xx and STM32F107xx microcontrollers.
   
 * <h3><center>&copy; COPYRIGHT 2009 STMicroelectronics</center></h3>
 */
